Negative total energy value using compressible model

Questions and remarks about code_saturne usage
Forum rules
Please read the forum usage recommendations before posting.
Post Reply
roberto.bernetti
Posts: 35
Joined: Tue Apr 16, 2019 10:03 pm

Negative total energy value using compressible model

Post by roberto.bernetti »

I tried to run a compressible calculation on version 7.04 downloaded from the web site installed on a ubuntu WSL2.
I cant upload the mesh, too data. This is the error that I get

Code: Select all

SIGSEGV signal (forbidden memory area access) intercepted!

Call stack:
   1: 0x7fa418641cfd <typecl_+0x3a78>                 (libsaturne-7.0.so)
   2: 0x7fa4184dfd30 <condli_ini_+0x40f>              (libsaturne-7.0.so)
   3: 0x7fa4184ab218 <caltri_+0x748>                  (libsaturne-7.0.so)
   4: 0x7fa419371b97 <main+0x717>                     (libcs_solver-7.0.so)
   5: 0x7fa4182070b3 <__libc_start_main+0xf3>         (libc.so.6)
   6: 0x56420519308e <_start+0x2e>                    (cs_solver)
End of stack
Attachments
setup.xml
(10.41 KiB) Downloaded 54 times
Saluti
Roberto
roberto.bernetti
Posts: 35
Joined: Tue Apr 16, 2019 10:03 pm

Re: PROBLEM IN THE BOUNDARY CONDITIONS USING COMPRESSABLE MODEL

Post by roberto.bernetti »

I overcome the previous errror checking the "hydrostatic equilibrium at wall" box.
But now I got the following error:

Code: Select all

Error in thermodynamics computations for compressible flows
:
Negative values of the internal energy were encountered in 1 cells.



Call stack:
   1: 0x7fed4f7d9dc5 <cs_cf_check_internal_energy+0x2d5> (libsaturne-7.0.so)
   2: 0x7fed4f7d054e <cfener_+0x1863>                 (libsaturne-7.0.so)
   3: 0x7fed4f323154 <scalai_+0x6e5>                  (libsaturne-7.0.so)
   4: 0x7fed4f32dbd9 <tridim_+0x44a1>                 (libsaturne-7.0.so)
   5: 0x7fed4f19c6ff <caltri_+0x1c2f>                 (libsaturne-7.0.so)
   6: 0x7fed50061b97 <main+0x717>                     (libcs_solver-7.0.so)
   7: 0x7fed4eef70b3 <__libc_start_main+0xf3>         (libc.so.6)
   8: 0x55cfc237008e <_start+0x2e>                    (cs_solver)
End of stack
Saluti
Roberto
Yvan Fournier
Posts: 4070
Joined: Mon Feb 20, 2012 3:25 pm

Re: PROBLEM IN THE BOUNDARY CONDITIONS USING COMPRESSABLE MODEL

Post by Yvan Fournier »

Hello,

Thanks for the feedback on the previous thread.

But please do not hijack an existing thread, at least when it is old. This makes searching through the history more difficult for us, as if we go back a few posts, we will see different explanations.

I made the same remark to another user on this same thread. So if you read this thread, you must have seen it. this remark applies to everyone. So please create a new thread instead.

Also, try to post a longer part of the error message. I do not even know whether you have a SIGSEGV, floating-point exception,
or other type of error, and this information is essential for debugging...

Best regards,

Yvan

[edit : I have split this thread from the previous one]
roberto.bernetti
Posts: 35
Joined: Tue Apr 16, 2019 10:03 pm

Re: PROBLEM IN THE BOUNDARY CONDITIONS USING COMPRESSABLE MODEL

Post by roberto.bernetti »

Thanks.
I'll create a new thread.
Saluti
Roberto
Post Reply