Please could you help me with these errors?
I use version 7.1-alpha from GitHub's master branch. For a case I finished LES calculation in the incompressible module, I now want to run it in the compressible module, for comparison. But in the compressible module, the calculation crashed at the beginning. The errors are shown below:
Code: Select all
CALCULATION PREPARATION
=======================
===========================================================
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ @@ WARNING : WHEN READING INPUT DATA
@ =========
@ CHOICE OF TIME-SCHEME
@
@ TIME-SCHEME FOR VELOCITY IS SECOND ORDER
@ (THETAV = 0.50E+00)
@ SOME TERMS ARE HOWEVER FIRST ORDER IN TIME WITH
@ THE FOLLOWING SETTINGS:
@
@ parameters ISTMPF ISNO2T ISTO2T IROEXT IVIEXT ICPEXT
@ Values entered 2 1 0 0 0 0
@
@ computation will go on.
@
@ Check the input data.
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ @@ WARNING:
@ =========
@ OPTIONS NOT VALIDATED WITH TIME DICRETISATION SCHEME
@
@ The current version is not validated with this time
@ discretisation scheme when a specific physics is active
@ (combustion, coal, electrical, ...).
@
@ Verify the parameters.
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
Error while reading numerical parameters for variable Pressure
-----
Parameter: var_cal_opt.thetav (theta-scheme) = 0.5
while its value must be equal to 1 .
Error in LES, while reading convection scheme parameters for variable Velocity
-----
Parameter: var_cal_opt.blencv (2nd order scheme share for convection) = 0
while its value must be in range [0.95 , 1 ].
Warning in LES, while reading convection scheme parameters for variable Velocity
-------
Parameter: var_cal_opt.blencv (2nd order scheme share for convection) = 0
while its recommended value is equal to 1 .
Error in LES, while reading convection scheme parameters for variable TotEner
-----
Parameter: var_cal_opt.blencv (2nd order scheme share for convection) = 0
while its value must be in range [0.95 , 1 ].
Warning in LES, while reading convection scheme parameters for variable TotEner
-------
Parameter: var_cal_opt.blencv (2nd order scheme share for convection) = 0
while its recommended value is equal to 1 .
Error in LES, while reading convection scheme parameters for variable temperature
-----
Parameter: var_cal_opt.blencv (2nd order scheme share for convection) = 0
while its value must be in range [0.95 , 1 ].
Warning in LES, while reading convection scheme parameters for variable temperature
-------
Parameter: var_cal_opt.blencv (2nd order scheme share for convection) = 0
while its recommended value is equal to 1 .
/home/ruonanwang/code_saturne/code_saturne-master/src/base/cs_parameters_check.c:790: Fatal error.
4 parameter error(s) reported.
Read error messages above for details, then
check your data and parameters (GUI and user subroutines).
Call stack:
1: 0x7f0017874472 <cs_parameters_error_barrier+0x82> (libsaturne-7.1.so)
2: 0x7f00178751a5 <cs_parameters_check+0xd05> (libsaturne-7.1.so)
3: 0x7f001791058b <initi1_+0x260> (libsaturne-7.1.so)
4: 0x7f00188af7cd <main+0x5dd> (libcs_solver-7.1.so)
5: 0x7f0016bc0bf7 <__libc_start_main+0xe7> (libc.so.6)
6: 0x5643edc72dfa <_start+0x2a> (cs_solver)
End of stack
Best regards,
Ruonan
(Sorry the mesh size is large so I didn't attach it. But I am very happy to send it to you by email if needed.)