Hello Andrea,
Nice video!
Do you update the head loss factor in each iteration? Or you lead to the fluid flow to adapt to the new head loss factor distribution.
Regards,
Luciano
Search found 282 matches
- Sun Nov 20, 2016 11:02 pm
- Forum: code_saturne usage
- Topic: Topological Optimizazion in Code Saturne
- Replies: 12
- Views: 13113
- Fri Nov 18, 2016 4:03 pm
- Forum: code_saturne usage
- Topic: Topological Optimizazion in Code Saturne
- Replies: 12
- Views: 13113
Re: Topological Optimizazion in Code Saturne
Hello Andrea, Are you following th advice of Yvan ("...you may want to increase the value progressively")? This will allow that the fluid flow adapt to the new viscosity distribution, avoiding strong jumps in the velocity. Is your penalization function continuos in terms of "k"? ...
- Wed Nov 16, 2016 7:04 pm
- Forum: code_saturne usage
- Topic: Backflow problem in LES
- Replies: 9
- Views: 9522
Re: Backflow problem in LES
Muhsin, In sections 5.2 and 5.4.4 of the theory guide of CS ( http://code-saturne.org/cms/sites/default/files/docs/4.0/theory.pdf ) you can find a more detailed answer to this question. Outlet BC " Warning: if the outgoing mass-flux is negative, i.e. if the outlet becomes an inlet, then the mas...
- Wed Nov 16, 2016 5:41 pm
- Forum: code_saturne usage
- Topic: Backflow problem in LES
- Replies: 9
- Views: 9522
Re: Backflow problem in LES
Hello Mushin, I don't understand your question..but in your listing file you have a negative mass flow at inlet and a positive mass flow at outlet. The sign of the mass flow at boundaries depends on the sign of \vec{V} \cdot \vec{n} . When you activate the gravity, Are you also impousing a velocity ...
- Wed Nov 16, 2016 4:09 pm
- Forum: code_saturne usage
- Topic: Backflow problem in LES
- Replies: 9
- Views: 9522
Re: Backflow problem in LES
Hello Mushin, I was looking at your listing file. At start of your simulation you have an important density difference (481.81 MIN, 589.92 MAX) so, this could lead an important bouyancy (body) force. Did you try to reduce the value of the imposed gravity in order to reduce this forces? Because, as y...
- Mon Nov 14, 2016 4:25 pm
- Forum: code_saturne usage
- Topic: Backflow problem in LES
- Replies: 9
- Views: 9522
Re: Backflow problem in LES
Hello Mushin,
Could you solve your problem? If not, could you upload a small problem where the case fails.
Regards,
Luciano
Could you solve your problem? If not, could you upload a small problem where the case fails.
Regards,
Luciano
- Mon Nov 14, 2016 4:11 pm
- Forum: code_saturne usage
- Topic: Internal wall not detected in code saturne 4.2
- Replies: 14
- Views: 11981
Re: Internal wall not detected in code saturne 4.2
Hello Sagar, I uploaded an user function and a case file where your problem it is working (I attach a figure). I used the default values in the user fuction like in the /REFERENCE/cs_user_mesh.c using as selection criteria "8" and the same selection criteria in the GUI to impose the wall B...
- Wed Nov 09, 2016 10:59 pm
- Forum: code_saturne usage
- Topic: Heated square cavity flow Tutorial 3 in Code Saturne 4.0
- Replies: 11
- Views: 11011
Re: Heated square cavity flow Tutorial 3 in Code Saturne 4.0
Hello,
I didn't find anything strange in the listing. I attach a case file and a mesh which I get the solutions like in the tutorial.
Try to compare this case file with your case file in order to find the difference,
Regards,
Luciano
I didn't find anything strange in the listing. I attach a case file and a mesh which I get the solutions like in the tutorial.
Try to compare this case file with your case file in order to find the difference,
Regards,
Luciano
- Wed Nov 09, 2016 4:45 am
- Forum: code_saturne usage
- Topic: Heated square cavity flow Tutorial 3 in Code Saturne 4.0
- Replies: 11
- Views: 11011
Re: Heated square cavity flow Tutorial 3 in Code Saturne 4.0
Hello,
Are you following the tutorial? The expected results are shown at the end of the pdf.
Could you post the listing file.
Regards,
Luciano
Are you following the tutorial? The expected results are shown at the end of the pdf.
Could you post the listing file.
Regards,
Luciano
- Mon Nov 07, 2016 3:06 pm
- Forum: code_saturne usage
- Topic: free surface not moving
- Replies: 21
- Views: 15478
Re: free surface not moving
Hello Olivier, I was debuging the alelav.f90 subroutine and I found that may be there is a bug in the following line, because to get the type of boundary condition at the boundary face ifac is used itypfb(ifac). if (ialtyb(ifac) .eq. ifresf) then so if you change to if (itypfb(ifac).eq.ifresf) then ...