In addition to the last post, how can I calculate the mass flow rate for each cell?
Kind regards,
Costas
Search found 48 matches
- Mon May 21, 2018 2:12 pm
- Forum: code_saturne usage
- Topic: cs_user_source_terms
- Replies: 4
- Views: 2288
- Sun May 20, 2018 11:38 pm
- Forum: code_saturne usage
- Topic: 2D_Simple_Channel_Flow
- Replies: 6
- Views: 3214
Re: 2D_Simple_Channel_Flow
Hello Yvan,
Thanks again for your response. Yes I have found how to impose heat flux in GUI but I want to extract the Tplus along a line (i.e cells and boundary ) by printing the results in a different file (i.e csv)
Cheers,
Constantinos
Thanks again for your response. Yes I have found how to impose heat flux in GUI but I want to extract the Tplus along a line (i.e cells and boundary ) by printing the results in a different file (i.e csv)
Cheers,
Constantinos
- Sun May 20, 2018 11:35 pm
- Forum: code_saturne usage
- Topic: cs_user_source_terms
- Replies: 4
- Views: 2288
Re: cs_user_source_terms
Hello Yvan,
Thank you for your response. I was a bit confused with the cell_f_vol because basically I want to impose a uniform heat flux on the boundary walls and have the source term on the cells to balance out.
Regards,
Costas
Thank you for your response. I was a bit confused with the cell_f_vol because basically I want to impose a uniform heat flux on the boundary walls and have the source term on the cells to balance out.
Regards,
Costas
- Fri May 18, 2018 4:49 pm
- Forum: code_saturne usage
- Topic: cs_user_source_terms
- Replies: 4
- Views: 2288
cs_user_source_terms
Hi guys,
I wanted to ask you if it is possible and how can I select only the fluid volumes (cells) to impose a source term on them and exclude the boundary faces.
Thanks.
Costas
I wanted to ask you if it is possible and how can I select only the fluid volumes (cells) to impose a source term on them and exclude the boundary faces.
Thanks.
Costas
- Thu May 17, 2018 12:06 pm
- Forum: code_saturne usage
- Topic: 2D_Simple_Channel_Flow
- Replies: 6
- Views: 3214
Re: 2D_Simple_Channel_Flow
Hi, A few more questions related to the same 2D_channel flow case. 1)What subroutine shall I use if I want to impose uniform heat flux on wall boundaries for my channel? 2)Can this be done via GUI? 3) How can I print the value of Tplus for each cell along a y-direction line? Kind Regards, Constantinos
- Mon May 14, 2018 9:44 pm
- Forum: code_saturne usage
- Topic: 2D_Simple_Channel_Flow
- Replies: 6
- Views: 3214
Re: 2D_Simple_Channel_Flow
Yvan,
Many thanks.
Constantinos
Many thanks.
Constantinos
- Mon May 14, 2018 3:43 pm
- Forum: code_saturne usage
- Topic: 2D_Simple_Channel_Flow
- Replies: 6
- Views: 3214
2D_Simple_Channel_Flow
Hello guys, I am new user to Code_Saturne and I have set a simple channel flow case with periodic inlet/outlet. The dimensions of my geometry is 1m along x-direction (periodic), 1m along z-direction (symmetry) and 2m along y-direction (top and bottom walls). I have generated a hexahedral mesh with 4...
- Mon May 14, 2018 12:14 pm
- Forum: Discussion
- Topic: 2D_channel_flow
- Replies: 1
- Views: 2819
2D_channel_flow
Hello guys, I am new user to Code_Saturne and I have set a simple channel flow case with periodic inlet/outlet. The dimensions of my geometry is 1m along x-direction (periodic), 1m along z-direction (symmetry) and 2m along y-direction (top and bottom walls). I have generated a hexahedral mesh with 4...